Menvier Security TS700 Especificaciones descargar pdf (Pagina 35)

Remote Reset Algorithm

When the system is programmed for “Engineer

Reset” the requirement to send an engineer to site

can be overridden by the user by using the

“Remote Reset” facility. If an alarm is generated

the system will respond with a four digit “seed”

codewhichtheuserquotestotheAlarmReceiving

Centre or alarm company. The “seed” code is

then entered into a decoder and a unique

“Remote Reset” code is generated. This is passed

back to the user and on entering the “Remote

Reset” code, the system is reset.

The “Remote Reset” code is generated using an

algorithm identified by a 3 digit number.

Alternative algorithms can be selected but these

must correspond tothatusedby theARC(or alarm

company) otherwise the “Remote Reset” code will

be incorrect. (Default = 004)

Configuration

The configuration options are as follows:

00 Bell Is an SAB

When programmed as “Yes” the control panel

bell output applies 0V when active. When

programmed as “No” the control panel bell

output removes 0V when active. (Default =

Yes)

01 User 1 Limited

When programmed as “Yes” user 1 is disabled

from options 6 and 8 in user menu 2 , and all

options in user menu 3. When programmed as

“No” user 1 has access to all user menus and

options. (Default = No)

02 Fire Signals all

When programmed as “Yes” fire alarm

activationsaresignalled totheARCatalltimes.

When programmed as “No” fire alarm

activations are signalled to the ARC only when

the system is full set. (Default = No)

03 Silent 24hr Circuits

When programmed as “Yes” 24hr circuit are

silent. When programmed as “No” 24hr circuits

are audible. (Default = No)

04 Enable Duress

When programmed as “Yes” the reversalof the

first two digits on any passcode will generate a

duress alarm. When programmed as “No” the

reversal of the first two digits on any passcode

will NOT generate a duress alarm. (Default =

Yes)

05 Invert Abort O/P

When programmed as “Yes” the abort output

is normally active and deactivates for 5

seconds when an alarm is aborted. When

programmed as “No” the abort output is

normally inactive and activates for 5 seconds

when an alarm is aborted. (Default = No)

06 Set with Line Fault

When programmed as “Yes” the system can

be set with a telephone line fault, however the

user will be asked to confirm this at the time of

setting. When programmedas “No”the system

can not be set with a telephone line fault.

(Default = Yes)

07 User Reset

When programmed as “Yes" alarms can be

reset by the user. When programmed as ”No"

alarms can onlybereset by theengineer orvia

remote reset. (Default = Yes)

08 Constant Exit Tones

When programmed as “Yes" exit tones remain

constant during exit. When programmed as

”No" exit tones rise in pitch during exit. (Default

= Yes)

09 High Security Engineer

When programmedas“Yes"theengineermust

enter his passcode and remote reset number

to gain access to engineer's menu 1. When

programmed as ”No" only the engineer's

passcode is required to access engineer's

menu 1. (Default = No)

Remote Reset

Algorithm > 004

Remote Reset

Algorithm > 010

Engineers menu 1

Select Option :-

Algorithm No.

8

Enter new No.

e.g. 010

ENT

StarburstLCD

LED

E1-

ENGR 1 -

004

004

010

010

Remote Reset Algorithm Flowchart

TS900 Installation Manual Engineer's Menu 1

31

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 67 68

Comentarios a estos manuales

Sin comentarios