Menvier Security TS700 Especificaciones Pagina 19
- Pagina / 68
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Digicom/RedCARE Installation
Astandalonedigitalcommunicator,RedCARESTU
or Paknet interface card can be connectedto the
control panel using the following connections:
Digicom Outputs 1 to 8
These are the programmable digicom output
connections. They are normally at +12V and
switch to 0V when active. The outputs can be
inverted so that they switch from 0V to +12V when
active (see System Configuration on page 31).
Each outputwillsource5mAin the+12Vcondition
and sink 100mA in the 0V condition.
+DC POWER
This provides the +12V power to the digicom. This
output is un-fused and therefore should only be
used if the digicom is fitted inside the control
panel. The 0V supply for the digicom/STU can be
picked up from any of the auxiliary 0V terminals.
LINE FLT
When this input is switched to +12V, a “Line Fault”
condition is generated. A “Line Fault” condition In
the unset mode will cause a “Chime” type tone to
be generated every minute, which can be
silenced by entering any valid passcode. A “Line
Fault” condition In the set mode will cancel the
“Bell Delay”.
Plug-on Digicom Installation
A plug-on digital communicator DC54 or DC58
may be fitted inside the control panel to allow
alarm status information to be transferred to a
dedicated centralstation.The unitshould befitted
in accordance with the installation instructions
supplied with it and connected to the control
panel plug DIGI-MODEM (JP3) using the lead
provided with the unit, see Figure 21. The NVM
within the digicom can be programmed via the
control panel, see page 48.
Plug-on digi-Modem Installation
A plug-on digi-modem DC58M may be fitted
inside the control panel to allow remote
interrogation and programming via a personal
computer (PC). It will also function as a standard
digicom (if required). The unit should be fitted in
accordance with the installation instructions
supplied with it and connected to the control
panel plug DIGI-MODEM using the lead provided
with the DC58M. The NVM within the digi-modem
can be programmed via the control panel, see
page 48. The modem data is also programmed
via the control panel.
Control
Panel
3GSTU
1
1
+DC POWER
Program
As:-
Open (060)
Alarm (005)
PA (006)
Fire (007)
LINE FLT
AUX 0V
2
2
3
3
4
4
5
TB1
Channel Inputs are
Programmed as
Positive Removed
TB2
TB3
TB4
Control
Line
Fault RPS
5
6
6
7
7
0V
NO
NO
NO
NC
NC
NC
8
8
C C
C
A+ A+ A+ A+ V+
Figure 20 3GSTU RedCARE Connections
Connect to JP7
DIGI-MODEM
Plug-on digicom / digi-modem
A
B
BC
B.T. master jack ( Type NTE5
user accessible connections )
A(5) = White / Blue ring
BC(3) = Blue / White ring
B(2) = Orange / White ring
Telephone cable
(Type 1/0.5mm CW1308)
6
6
5
5
4
4
3
3
2
2
1
1
Figure 21 DC54/DC58 Connections
TS790 & TS900 Installation Manual System Installation
15
- TS790 & TS900 1
- Contents 3
- Engineers Menu 3 4
- Appendices 4
- Overview 5
- Remote Keypads 6
- TS900 NODE 6
- ID Node (TS900.IDNODE) 6
- TS700 LEC 6
- Specifications 6
- Cable Routing 7
- Remote Network Wiring 8
- Control Panel Installation 9
- Control Panel PCB Layout 10
- TS900 LCD Remote Keypad 12
- TS790 Star Remote Keypad 12
- TS700 LED Remote Keypad 13
- TS700 Remote Arming Station 13
- Installation Procedure 13
- Engineer’s Keypad 14
- TS900 Node Layout 15
- Double Pole 16
- End Of Line 17
- Auxiliary Tamper 18
- Extension Loudspeakers 18
- Digicom/RedCARE Installation 19
- Plug-on Digicom Installation 19
- Using the CPA6 Printer 20
- Control Panel Outputs 21
- Node Outputs 21
- Pre Power-Up Checks 22
- Initial Power-Up 22
- Power-Up Checks 23
- NVM Defaults 23
- Engineer’s Menu 1 25
- Menu contents 25
- Panel Outputs 26
- Digicom Outputs 26
- Digicom Channels 26
- Programmable Output Types 26
- Circuit Types 29
- Circuit Attributes 30
- System Timers 31
- StarburstLCD 34
- Remote Reset Algorithm 35
- Configuration 35
- View Location Text (LCD Only) 38
- Engineer's Menu 2 39
- Menu Contents 39
- View Circuits 40
- Set System Time 40
- Set System Date 40
- Change Passcode 40
- Log Event Codes 42
- View System Log 42
- Reset User Code 1 44
- Start Call Back 44
- Time Switches 46
- Part Set Group Operation 47
- Code Set Group Operation 47
- Reset Message 48
- Banner Message 48
- Built In Tests 49
- View Inactive Circuits 50
- Custom Outputs A & B 51
- Modem Options (LCD Only) 52
- Program Digi Flowchart 53
- Reset Digicom 54
- Workshop Canteen 59
- Service Department 59
- Key Point Application Example 60
- Control Panel 61
- Text Editing Keys 62
- TS790/TS900 62
- User Types 63
- Setup New Users Flowchart 64
- Engineers Menus 66
- User Menus 66
- SECURITY 68
© 2020, manymanuals.es. Todos los derechos reservados | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales