Menvier Security TS2500 Guía de usuario descargar pdf (Pagina 7)

Connection Terminals, Plugs & Indicators

The main PCB has the following connectors etc.

1 Networks 1-8

Data networks for connecting NODEs, remote

keypadsandLECs.Eachnetworkisprotectedby

its respective fuse (30), the fuse is in-line with the

[A] connection of the network

2 Auxiliary 12V

Three sets of auxiliary 12V terminalsare provided

onthemainPCB,eachsetprovidesdcpowerfor

detectors etc. These outputs are protected by a

1A fuse (32).

3 Battery Terminals

Connection terminals for the red and black

battery leads supplied inside the spares pack.

4 Earth Terminal

Connection to mains earth.

5 AC Input Terminals

The output from the mains transformer is

connected into these two terminals.

6 External Sounder Terminals

This group of terminals are used for connection

to an external sounder.

7 Speaker Terminals

Up to two 16 ohm extension loudspeakers can

be connected across these two terminals. The

volumeiscontrolledviaaprogrammingoption.

8 Auxiliary Tampers1&2

These terminals provide tamper protection to

auxiliarydevicessuchas remotepowersupplies,

extension loudspeakers etc. If they are not used

they must be linked out.

9 Remote Reset Input

After a full alarm the system will require resetting,

normally this is done by the engineer or via

coded remote reset. By applying a -ve to this

input terminal it will cause the system to reset

after a fullalarm. This input couldbe connected

to the “Control” output on a RedCARE STU so that

thecentralstationcanprovidea“RemoteReset”

facility.

10 Line Fault Input

When this input is applied with a +ve signal the

system will generate a “Line Fault” condition. In

the unset condition the system will generate a

“Chime” tone every minute. In the set condition

any programmed bell delay is cancelled.

11 +DC Power

This terminal provides the +12V power to the

stand-alone digital communicator or RedCARE

STU. This output is un-fused and therefore must

only be used if the device is fitted inside the

control panel housing.

12 Digicom Outputs 1 to 8

These are programmable outputs and are

normally connected to the input channels on a

stand-alone digital communicator or RedCARE

STU.Theoutputsarenormallyat+12Vandswitch

to 0V when active. The outputs can be inverted

sothattheyswitchfrom 0V to +12V whenactive

Each output will source 5mA in the +12V

condition and sink 100mA in the 0V condition.

13 Panel Outputs 1 to 4

These are programmable outputs that can be

used to drive relays and auxiliary equipment.

Output [1] is a set of voltage free change over

contactratedat 1Amp. Output [-2] is aswitched

negative output rated at 500mA. Outputs [+3]

and [+4] are switched positive outputs rated at

500mA.

14 Printer Output Port (JP1)

This 6-pin plug is used for connecting to either a

CPA6 printer or a standard RS232 printer via the

DCI/MPA printer adaptor.

15 Output Module (JP2)

Output modules type CPA6.OM can be

connected to this 5-pin plug, and are used to

provide switched -ve outputs to LED's/relays etc.

Theoutputscan be programmed such thatthey

give ward status information and/or circuit

mimic/alarm indications.

16 LEC 1 (JP3) / LEC 2 (JP4)

Two LEC8 PCBs can be connected via an

interface lead to these connectors. The

interface lead is provided with the LEC8.

17 Factory Restart (JP5)

If these pins are shorted during power-up all

system parameters are reset to their factory

defaultsettings.Iftheengineer’spasscodeislost

orforgotten it can be resetto1234withoutlosing

any other program data as follows:

(a) Ensurethat thesystem is fullyunset anda user

passcode is available.

(b) Removethecoverfromthecontrolpanel,this

will cause a panel lid tamper alarm.

(d) Place the blade of a small screwdriver

between the “FACTORY RESTART” pins. A

multi-tonesoundindicatesthattheengineer’s

passcode has been reset. This action will be

recorded in the system log.

TS2500

496513 Issue A 7of26 TS2500

1 2 3 4 5 6 7 8 9 10 11 12 ... 25 26

Comentarios a estos manuales

Sin comentarios

Menvier Security TS2500 Guía de usuario Pagina 7

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Menvier Security TS2500