Menvier Security TSD401 Guía de usuario descargar pdf (Pagina 4)

Connections & Controls

The main PCB has the following “Jumper Plugs” (JP),

indicator LEDs and terminal connections.

TRIG POLARITY (JP1)

This jumper-link sets the signal polarity for the auxiliary

speech dialler trigger inputs. The inputs may be either

+ve to trigger or -ve applied to trigger.

SPEAKER (JP2)

The internal loudspeaker has a 2-way connector which

plugs directly on to this set of pins.

FACTORY RESET (JP3)

All program data (not messages) is stored in a

Non-Volatile Memory chip (NVM). If the Factory Reset

pins are shorted during power-up all stored system

parameters are over written with the factory default

settings. Theengineerpasscodeisresetto1234andthe

User 1 passcode is set to 5678.

EXT. VOLUME (VR1)

If an extension loudspeaker is connected to the control

panel, the volume of keypad bleeps, chime, entry and

exit tones may be adjusted using this control (clockwise

to increase). Alarm tones are always full volume.

INT. VOLUME (VR2)

This controls the volume ofkeypad bleeps, chime, entry

and exit tones from the internal loudspeaker (clockwise

toincrease). The volume of thespeechdiallerplayback

messages are always full volume.

Installing a TS400 Remote keypad

Up to four TS400 remote keypads may be connected to

the TSD402 control panel. The remote keypad is

supplied with an interface PCB which plugs onto the

main PCB. Remote keypad(s) may be sited up to a

maximum of 50 metres from the control panel using a

six-core cable for connections.

☞

TheTS400remotekeypadisonlysuitablefor

setting, part-setting, unsetting and limited

programming functions. All other system

operations must be carried out at the

control panel.

1. Remove the TSD402 PCB from the case

2. Connect each core of the six-core cable to

the interface terminals "LEDCBA" (make a

note of the colours used for each

connection).

3. Pass the yellow flying-lead behind the PCB

and connect it to the L/S-terminal.

4. Plug the interface PCB onto the TSD402 PCB.

(See figure on page 3).

5. Replace the TSD402 PCB.

6. Separate the remote keypad cover and

base by using a screwdriver to push two of

the clips (top or bottom) inwards from the

cover retaining slots. Then lift the cover

assembly away, noting that the PCB is

connected to the under side of the cover.

7. Hold the remote keypad base in position

(keyhole to the top) and mark the three

securing holes, drill and plug the wall as

required. Pass the six-core cable into the

base via the cable entry points as

appropriateandsecure the basetothewall.

8. Connect each core of the six-core cable to

the remote keypad terminals "EDCBAL",

ensuring that the connections through to

the control panel are A-A, B-B, C-C etc. If

more remote keypads are to be fitted, they

may be connected in a "Star" or

"Daisy-chain" configuration (providing the

cable length to the last or furthest remote

keypad does not exceed 50 metres).

9. Carefully reattach the front cover assembly

to the remote keypad base ensuring that all

cables are clear of the tamper switch spring

and the cover is securely clipped to the

base.

TSD402 & TSD401

TSD402 & TSD401 4of10 496523 Issue A

1 2 3 4 5 6 7 8 9 10

Comentarios a estos manuales

Sin comentarios

Menvier Security TSD401 Guía de usuario Pagina 4

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Menvier Security TSD401