Menvier Security TS900+ Especificaciones Pagina 20
- Pagina / 68
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Output Modules Installation (CPA6.OM)
Output Modules (CPA6.OM) can be used to
provide a set of outputs to LEDs or relays to indicate
either circuit alarm activations or circuit mimic
activations. The first output module connected to
the system will indicate circuits 1 to 8, the next
modules will indicate circuits 9 to 16 etc. Output
modules are normally fitted inside the equipment
they are controlling and may be positioned up to
500 metres away from the main panel. The output
module should be used and connected in
accordance with the instructions provided with it.
Connecting a Printer
The TS790/900 supports two type of printers, the
CPA6 printer (no longer available) and any
standard RS232 printer. When using an RS232
printer a DCI/MPA printer adaptor will be required.
Menvier Security supply a DATAC printer kit which
consists of a portable RS232 printer, charger unit
and DCI/MPA adaptor.
Using the CPA6 Printer
1. Plug the CPA6 printer directly on to the PRINTER
plug (JP1) on the main control panel PCB.
2. The printer will printout a header, when finished
the system program details and event log can
be printed.
3. When finished unplug the printer. If the printer is
left connected events will be printed as and
when they occur.
Using the DATAC / RS232 Printer
1. Plug the DCI/MPA on to the PRINTER plug (JP1)
on the main control panel PCB.
2. Plug the other end of the DCI/MPA into the
DATAC or RS232 printer.
3. In order for the printer to work correctly ensure
the printer is set to the following:
Baud rate = 4800
Parity = None
Start bits = 1
Stop bits = 2
Data bits = 8
DTR = Normal
4. When set-up correctly the system program
details and event log can be printed.
5. When finished unplug the MPA/DCI. If the
printer is left connected events will be printed
as and when they occur.
16
System Installation TS790 & TS900 Installation Manual
PL1
1k Resistors
LED's
1234
567
+12V IN
+12V OUT
+12V OUT
8
PL2
To next OM
Connect to plug
labelled OUTPUT
MODULE
100m
Figure 21 Output Module Connections
DC58M
Telephone
Network
V21.
Modem
Alarm Receiving
Centre
TS790/900 Control
Panel
Figure 20 DC58M Digi-modem Schematic
- TS790 & TS900 1
- Overview 3
- System Installation 3
- Engineer’s Menu 1 3
- Engineer's Menu 2 3
- Engineers Menu 3 4
- Appendices 4
- System Architecture 5
- Control Panel 5
- Remote Keypads 6
- TS900 NODE 6
- ID Node (TS900.IDNODE) 6
- TS700 LEC 6
- Specifications 6
- Cable Routing 7
- Remote Network Wiring 8
- Control Panel Installation 9
- Control Panel PCB Layout 10
- NETLCD Remote Keypad 12
- NETSTAR Remote Keypad 12
- NETLED Remote Keypad 12
- NETARM Remote Arming Station 12
- PCB Layouts & Connections 12
- Tamper Switch 13
- ENT Key Disable 13
- Engineer’s Keypad 14
- Figure 11. TS900 Node Layout 15
- TS700 LEC Installation 16
- Wiring Detection Circuits 16
- External Sounder Connections 17
- Auxiliary Tamper 18
- Extension Loudspeakers 18
- Digicom/RedCARE Installation 19
- Plug-on Digicom Installation 19
- Connecting a Printer 20
- Programmable Outputs 21
- Pre Power-Up Checks 22
- Initial Power-Up 22
- Power-Up Checks 23
- NVM Defaults 23
- Introduction 25
- Panel Outputs 26
- Digicom Outputs 26
- Digicom Channels 26
- Programmable Output Types 26
- Program Circuits 29
- Circuit Attributes 30
- System Timers 31
- Setting Modes 34
- Do System Print 34
- Remote Reset Algorithm 35
- Configuration 35
- Goto User Menu 1 37
- View Location Text (LCD Only) 38
- Relearn Hardware 38
- View Circuits 40
- Set System Time 40
- Set System Date 40
- Change Passcode 40
- Chime Circuits 41
- Alter 24Hr Group 41
- Print System Log 41
- Configure Wards 41
- Log Event Codes 42
- View System Log 42
- StarburstLCD 44
- Menu Contents 45
- Time Switches Flowchart 46
- Part Set Group Operation 47
- Code Set Group Operation 47
- Reset Message 48
- Banner Message 48
- Location Text 49
- Printer Header 49
- Part Set Banner 49
- Current Consumption 49
- View Inactive Circuits 50
- Custom Outputs A & B 51
- Modem Options (LCD Only) 52
- Program Digi Flowchart 53
- Reset Digicom 54
- Point ID Extended Reporting 55
- Workshop Canteen 59
- Service Department 59
- Key Point Application Example 60
- Text Editing Keys 62
- Setup New Users 63
- Setup New Users Flowchart 64
- 496487 Issue 3 68
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Menvier Security TS900+
Los Sistemas De Control De Acceso De Seguridad Menvier Security TS700 Manual de usuario
(16 paginas)
(16 paginas)
Los Sistemas De Control De Acceso De Seguridad Menvier Security TS2500 Manual de usuario
(60 paginas)
(60 paginas)
Los Sistemas De Control De Acceso De Seguridad Menvier Security TS400 Manual de instrucciones
(32 paginas)
(32 paginas)
Los Sistemas De Control De Acceso De Seguridad Menvier Security TS700 Manual de instrucciones
(32 paginas)
(32 paginas)
Los Sistemas De Control De Acceso De Seguridad Menvier Security TS700 Manual de usuario
(10 paginas)
(10 paginas)
Los Sistemas De Control De Acceso De Seguridad Menvier Security TS2500 Manual de usuario
(48 paginas)
(48 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.024 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales